Run an Ethernet Cable Through Walls While making your home, it may be possible that you forgot to push up an ethernet cable connection in the walls. So, you need to run an ethernet cable in the wall through an external source. So, check up for the connection in the ethernet lines when you notice no ethernet cables in your home. 

All you need to do is to drill up a simple hole into the exterior portion of the wall. While drilling, ensure not to drill up other wires or ducts in the wall. Now, run the ethernet cable in the location. As the last step, seal the hole among the line using silicone caulk to secure water infiltration. In detail, let us see some stages that How To Run an Ethernet Cable Through Walls?

How Difficult Is It to Run Ethernet Cable Through Walls? 

Run an Ethernet Cable Through Walls The toughness of running an Ethernet cable through walls depends on your wall. For example, if you have drywall, you will find assembling relatively easy. But, as for the brick or concrete walls, the installation process is challenging. 

Suppose you notice that each side of the wall is dehydrated. You can take the help of a screwdriver to drill the hole. This hole should be big enough to fit the ethernet cable into the wall. After fixing the hole, install the plug and wires around. 

Point to ponder

Also, keep in mind that the hole should be tiny and unnoticeable once you are done with setting the plug. It’s time to patch and repaint the drilled surface. A perfect drilling point is always the one attached and held close to the ground. Never drill up on the other wires or plumbing. 

In the case between the operation, you notice any hurdle. Switch up the cut right away and move six inches away. You can then continue the process. As for the brick wall, run the metal tube into the wall and get success. However, the whole process is a bit messy but is never impossible.   

Also read: How to make an Ethernet cable?

Which One Is Better: Flat or Round Ethernet Wire? 

Run an Ethernet Cable Through Walls Well, round ethernet cables are more durable and sturdier than round wires. This is because flat ethernet cables are not water resistant and have less shielding power. So, rounded lines serve the purpose and get bonus points over the flat ones. Always remember: 

Round cables are insulated, secure and sturdy to use compared to flat ones. So, round wires are perfect even when used outdoors. 

Take the help of weather-checked and waterproof cable while selecting an ethernet cable wire for outdoor usage. Also, as for the exterior wall, you can run up a water-resistant cord. 

No matter whether you select a round or a flat ethernet cable. It would help if you ensured that the line is perfect according to your need. In short, if you tend to buy a cable for outdoor usage. Select a weatherproof and compatible cable. 

But in case you are working indoors, you can use any cable. 

Point to ponder

Suppose you don’t follow your requirements while buying. You may end up getting a breakdown. So, there can come a situation where you have to replace the cable even after a very short interval of time. Avoid the damage and secure your connection with a suitable cable.

Easy Steps for Running an Ethernet Cable Through Walls 

Run an Ethernet Cable Through Walls With fewer tools and steps. You can achieve the goal of installing a cable from the outside to the inside of the house. Let us follow the steps to get a stable and safe connection. So, 

Notice The Already Present Ethernet Cable 

Before moving towards drilling holes, check out whether your exterior walls have an ethernet cable installed or not. Notice that the ethernet cable should be directed to the box in your home if the line coming from your ISP ends towards your package. You are safe to use. 

However, if there is no cable, you need to proceed further toward the next steps. Commonly the ethernet cables lie in the basements and other short spaces. So, don’t forget to check there too. 

Selection Of Ethernet Cable 

The selection of a suitable ethernet cable is essential during installation. Always ensure that the best cable fulfils your requirements if you have to use a cable for outdoor purposes. Your cable should be weatherproof so that it doesn’t become destroyed quickly. 

Otherwise, you have to change the cable after every short interval. Check out the speed of the internet service arriving from ISP. Choose a cable compatible with that speed. Ethernet cables like cat8 and cat seven tackle the rate of more than 40 – 10 Gbps. However, some cables like cat6 and cat5 can only tackle the speed of about 1,000 to 10 Mbps. 

Select an ethernet cable
Ascending The Weatherproof Box 

Run an Ethernet Cable Through Walls The most crucial step while installing an ethernet cable in your home. It is to check that the line directing from ISP should be covered. If no covering is present, you must install a weatherproof box in your home. This box will help you secure the connection. 

When you know that no box is present, try to install one after checking the connection of the cable to the ISP. The container should be sturdy enough to handle every wear and tear. The weatherproof box should secure an ethernet cable point. 

Never compromise on the quality of the box. Because you need to secure your ethernet cables from rain, sunlight, and other weather conditions. 

Selection Of the Place 

You need to drill a hole into the wall when you know that no external ethernet line is present in your home. So, select the point of installing the cable. You need to be very careful while making a selection. The suitable position is to establish cable on the same wall as ISP. 

Important Note

So, it is essential to drill the hole in the area where there is no fear of damaging the plumbing, wiring, or ducts. Take the help of the scanner while drilling. The scanner will detect every other element coming into the wall. This is how you will be saved from damage. 

Drilling Holes 

After selecting the right place, it’s time to drill the hole. So, use a 13 mm drill bit at least 12 inches long. In case you are drilling the cable from the outside to the inside. It is recommended to use a drill from inside. In this way, you will be able to mark the location from where the cable needs to enter the home; however if you are planning on running the cable in the basement.

 It is recommended that you drill the hole from outside to inside space. In this way, you will face no difficulty while running the cable. 

Installing Cable in Hole 

Run an Ethernet Cable Through Walls When you are done with the hole drilling, you need to enter the cable in your home. So, use tape of a suitable thin length. Push the wire through the drilled hole. Now, go to the other side of the wall and pull the cable through it. 

Always notice that while installing the cable. There should be no twisting in the cable as bending can lead the cable to damage. 

Installing Jack 

When your cables are installed in the room, it’s time to wire up the line using a solid jack. After installing the jack, you will be able to plug up the cables in the jack. This method is highly recommended to save up your ethernet cables. 

Firstly, connect the cable with an ethernet jack in the wall. Now, run the cables through the jack to save them up and enhance their durability. 

Sealing Hole Along with Cable 

Run an Ethernet Cable Through Walls After the successful installation of the ethernet cable, installing the jack, covering up with the weatherproof box. Now, there comes a part where we need to weatherproof the drilled hole. So, use a silicone caulk and fill the hole present around the cables. 

Filling the hole secures your cables from the gap, water, and bugs. So, nothing will ever get inside the hole. However, when you need to replace the wires. You can easily remove the caulk using a sharp knife. Also, the caulk is super flexible and perfect for weatherproof conditions. 

Also Read: Chromecast Vs HDMI Cable – Which one to choose?

Wrapping it up!

Run an Ethernet Cable Through Walls

No doubt that wireless connections are also helpful. But, sometimes, you must rely on links like running an ethernet cable through the walls. Make sure to plan appropriately and mark every step before beginning the installation. 

Drill the holes, run the cables through them and install the jacks to prevent them. Every step is essential to get perfect results. 

Frequently Asked Questions